Post Wiki

User Tools

Site Tools

Trace:
mp:post_dev

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
mp:post_dev [2023/06/29 16:05] – russellmp:post_dev [2023/06/29 16:06] (current) – russell
Line 2: Line 2:
  
 == Lathe G112 face interpolation mode == == Lathe G112 face interpolation mode ==
 +\\
  
 Zoho ticket #24002 see 6/29/2023 response to client: Zoho ticket #24002 see 6/29/2023 response to client:
Line 8: Line 9:
 Thankfully, it is actually polar, it's just the C outputs are the Y positions. Thankfully, it is actually polar, it's just the C outputs are the Y positions.
 The post has this toggle because frequently, machine's need a C in front of the Y-axis polar positions, and on other machines as you mentioned, Y is required. The post has this toggle because frequently, machine's need a C in front of the Y-axis polar positions, and on other machines as you mentioned, Y is required.
 +\\
  
 ''g112address   : 1    #0 = Y, 1 = C''\\ ''g112address   : 1    #0 = Y, 1 = C''\\
  
 +\\
 So I have just switched this toggle and tested and I am returning a new PST/PSB to you with the Y label on all the Y polar positions. So I have just switched this toggle and tested and I am returning a new PST/PSB to you with the Y label on all the Y polar positions.
  
Line 18: Line 19:
 Please also note, if the rotary axis control setting in the toolpath is set to "no rotation" or "Y-axis" the post will respect this selection and initially position in XY, rather than XC, which I believe is not what you want, since the Y will not be at Y0: Please also note, if the rotary axis control setting in the toolpath is set to "no rotation" or "Y-axis" the post will respect this selection and initially position in XY, rather than XC, which I believe is not what you want, since the Y will not be at Y0:
  
 +\\
 <code> <code>
 G98 M134 P1000 G98 M134 P1000
Line 25: Line 27:
 G112 G112
 </code> </code>
 +\\
  
 It's important to set the rotary axis control to C-axis, since for polar, you're only using XCZ in reality: It's important to set the rotary axis control to C-axis, since for polar, you're only using XCZ in reality:
  
 +\\
 <code> <code>
 G98 M134 P1000 G98 M134 P1000
Line 35: Line 39:
 G112 G112
 </code> </code>
 +\\
  
 The above wouldn't matter if your machine didn't have an actual Y-axis. In that case the post would force XC always regardless of the setting. The above wouldn't matter if your machine didn't have an actual Y-axis. In that case the post would force XC always regardless of the setting.
  
 +\\
 == Post-Dev pre-Wiki Discussion Notes == == Post-Dev pre-Wiki Discussion Notes ==
 +\\
  
 A link to the document containing previous post-dev channel discussion is below: A link to the document containing previous post-dev channel discussion is below:
  
 [[https://docs.google.com/document/d/1wnNZhUMV2odXw2TCqSOLHTeagObDSOTaBKPWdW5OxCQ/edit#heading=h.hvrythw3zzsx|Post-Dev History Doc]] [[https://docs.google.com/document/d/1wnNZhUMV2odXw2TCqSOLHTeagObDSOTaBKPWdW5OxCQ/edit#heading=h.hvrythw3zzsx|Post-Dev History Doc]]
mp/post_dev.1688054710.txt.gz · Last modified: 2023/06/29 16:05 by russell

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki