Post Wiki

User Tools

Site Tools

Trace:
mp:mst_dev

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
mp:mst_dev [2024/04/24 19:05] – russellmp:mst_dev [2024/06/03 16:55] (current) – [CQM Posts - Future updates/improvements - Mass Updates] russell
Line 92: Line 92:
 == Tool inspection in CQM posts == == Tool inspection in CQM posts ==
  
-Use ''CQM_HAAS_EC_4X'' under ''Northrop Grumman Corp (Baltimore - Airport)'' [ #57083 ] to build proper tool inspection for CQM.\\ +Use ''CQM_HAAS_EC_4X'' under ''Northrop Grumman Corp (Baltimore - Airport)'' [ #57083 ] to build proper tool inspection for CQM masters.\\ 
-Note ''pretract_insp'' and ''pretract_cool_off_insp'' and ''pcool_on_insp''. +Note ''pretract_insp'' and ''pretract_cool_off_insp'' and ''pcool_on_insp''. This was built for X-style coolant. Test V9 style coolant.\\ 
 + 
 +== RAH plugin & Master == 
 + 
 +Improvements for simultaneous 5-axis style toolpaths in Brodeur machine ''YCM AGG A ABOUT Z'' post to move into RAH plugin and Master. Around 4/30/2024\\ 
 + 
 +== Okuma Macro Mult added to VMC masters == 
 + 
 +Also refine HMC version based on changes to JLG Industries COM_OKUMA_GENOS_4X delivered 5-9-2024 #32765\\ 
 + 
 +== prevent spindle stop if already stopped at change of spindle == 
 + 
 +pspindchng prevent spindle stop if already stopped at change of spindle.\\ 
 + 
 +Before:\\ 
 + 
 +<code> 
 +pspindchng      #Spindle speed change 
 +      if prv_spdir2 <> spdir2 & prv_speed <> zero, pbld, n$, *sm05, e$ 
 +      if not(canned_tap = 1),  #spind switch only on move line for LH tap - MU-0044 
 +        [ 
 +        if prv_speed <> speed | prv_spdir2 <> spdir2, 
 +          [ 
 +          if speed, 
 +            [ 
 +            pbld, n$, pgear, e$ 
 +            pbld, n$, pfspindle_out, e$ 
 +            ] 
 +          ] 
 +        !speed, !spdir2 
 +        ] 
 +</code> 
 + 
 +After:\\ 
 + 
 +<code> 
 +pspindchng      #Spindle speed change 
 +      if prv_spdir2 <> spdir2 & prv_spdir2 <> 1 & prv_speed <> zero, pbld, n$, *sm05, e$ 
 +      if not(canned_tap = 1),  #spind switch only on move line for LH tap - MU-0044 
 +        [ 
 +        if prv_speed <> speed | prv_spdir2 <> spdir2, 
 +          [ 
 +          if speed, 
 +            [ 
 +            pbld, n$, pgear, e$ 
 +            pbld, n$, pfspindle_out, e$ 
 +            ] 
 +          ] 
 +        !speed, !spdir2 
 +        ] 
 +</code> 
 + 
 +== Shortest direction 0-360 causes infinite loop with axis subs (pcoutrev) == 
 +\\ 
 + 
 +Change found to fix: 
 + 
 +Before: 
 + 
 +<code> 
 +pcoutrev        #Rotary axis revolution calculation (Modify for wind-up) 
 +      cdelta = csav - prv_csav 
 +      rev    = last_move_rev    #Reset rev  - MU-0068, rjj 
 +      ... 
 +      ... 
 +      ... 
 +      if index <> 1 & (rot_type > 0 | (one_rev & gcode$ = zero & (cuttype <> one | opcode$ = 3 | opcode$ = 16))), 
 +        [ 
 +        while fmtrnd(cabs) >= 360, 
 +          [ 
 +          cabs = cabs - 360 
 +          rev = rev - 1 
 +          ] 
 +        while fmtrnd(cabs) < 0, 
 +          [ 
 +          cabs = cabs + 360 
 +          rev = rev + 1 
 +          ] 
 +</code> 
 + 
 +After: 
 + 
 +<code> 
 +pcoutrev        #Rotary axis revolution calculation (Modify for wind-up) 
 +      cdelta = csav - prv_csav 
 +      rev    = last_move_rev    #Reset rev  - MU-0068, rjj 
 +      ... 
 +      ... 
 +      ... 
 +      if index <> 1 & (rot_type > 0 | (one_rev & gcode$ = zero & (cuttype <> one | opcode$ = 3 | opcode$ = 16))), 
 +        [ 
 +        while fmtrnd(cabs) >= 360, 
 +          [ 
 +          cabs = cabs - 360 
 +          if cuttype <> one, rev = rev - 1   #MU?? 
 +          ] 
 +        while fmtrnd(cabs) < 0, 
 +          [ 
 +          cabs = cabs + 360 
 +          if cuttype <> one, rev = rev + 1   #MU?? 
 +          ] 
 +</code>
  
 ===== CQL Posts - Future updates/improvements - Mass Updates ===== ===== CQL Posts - Future updates/improvements - Mass Updates =====
Line 237: Line 338:
 #       Param   Variable to load value into #       Param   Variable to load value into
  
 +</code>
 +
 +== MU related to above. Groove CC peck parameter change ==
 +
 +Groove peck amount MP documentation has wrong parameter. TESTED AND THIS WORKS.\\
 +
 +Before:\\
 +
 +<code>
 +fprmtbl 3 5 #Groove cut parameters
 +        13358 stepcc
 +        13138 directcc
 +        13352 dopeckcc
 +        13368 depthcc  #01/07/2013-was 10316 - MU-0009, rjj
 +        13364 clearcc
 +</code>
 +
 +After:
 +<code>
 +fprmtbl 3 5 #Groove cut parameters
 +        13358 stepcc
 +        13138 directcc
 +        13352 dopeckcc
 +        10316 depthcc  #01/07/2013-was 10316 - MU-0009, rjj
 +        13364 clearcc
 </code> </code>
  
Line 284: Line 410:
 Source: Latest MPLFAN has a swiss cheese of random additions to the lathe canned cycle area that are required. Will take some work to pin down how it differs from our master and add in the additions.\\ Source: Latest MPLFAN has a swiss cheese of random additions to the lathe canned cycle area that are required. Will take some work to pin down how it differs from our master and add in the additions.\\
 \\ \\
 +
 +== MU Lathe canned finish programmed feedrate output on G70 line ==
 +
 +Update to add feed rate entered on G70 canned finish line in lathe canned cycles.\\
 +starts at the fr_pos$ lines and ends after the output line.(4 lines)\\
 +
 +<code>
 +pread_g70       #Read G70 recall buffer
 +      foundcc = zero
 +      size2 = rbuf (two, zero)
 +      wc2 = one
 +      while wc2 <= size2 & foundcc = zero,
 +        [
 +        fcc_subid = rbuf (two, wc2)
 +        if fcc_subid = sub_op_id$,
 +          [
 +          gcodecc = zero
 +          ng70s = fcc_ng70s
 +          ng70e = fcc_ng70e
 +          fr_pos$ = opinfo(10030,0)   <-
 +          fr_pos$ = abs(fr_pos$)      <-
 +          pfcalc          #Feedrate calculations, gcode 0 does not evaluate    <-
 +          pbld, n$, *scclgcode, *ng70s, *ng70e, pffr, e$   <-
 +          foundcc = one
 +          rcc_flg$ = 7
 +          !rcc_flg$
 +          ]
 +        ]
 +      sav_seq = n$
 +      canneddone = two
 +      continue_seq = two  #10/30/2012-add MU-0002, rjj
 +</code>
 +
 +== MU Lathe pfcout signed direction doesn't have a C0 on first live tool op ==
 +
 +pfcout signed direction doesn't have a C0 on first live tool op.\\
 +Can place ''prv_c_wnd = c9k'' in ''pheader_out'' as a band aid fix that shouldn't affect anything else.\\
 +
 +<code>
 +pfcout
 +...
 +...
 +...
 +        else, #Signed direction, modality on c_wnd, no incremental
 +          [
 +          if fmtrnd(prv_c_wnd) <> fmtrnd(c_wnd),     #THIS CONDITION PREVENTS C0 at STARTUP if 1ST POSITION IS C0
 +            [
 +            if not(indx_mc = 0 & rot_dir = 0) & not(indx_mc = 1 & rot_dir = 1), result = nwadrs(sc_minus, cout_a)  #MU-0045 - Incl rot_dir, rjj
 +            else, result = nwadrs(str_cax_abs, cout_a)
 +            *cout_a
 +            ]
 +          !c_wnd, !cabs, !cinc
 +          ]
 +</code>
 +
 ===== CQL___MS Posts - Future updates/improvements File streamer CQP0010 stuff ===== ===== CQL___MS Posts - Future updates/improvements File streamer CQP0010 stuff =====
  
mp/mst_dev.1713985518.txt.gz · Last modified: 2024/04/24 19:05 by russell

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki